CCNA Discovery 3 Module 2 Exam Answers Version 4.0
1. What type of connection point is a point of presence (POP)?
• between a client and a host
• between two local networks
• between a computer and a switch
• between an ISP and an Enterprise network
Jawaban
2. A network administrator needs to configure Telnet access to a router. Which group of commandsenable Telnet access to the router?
• Router(config)# enable password class
Router(config)# line con 0
Router(config-line)# login
Router(config-line)# password cisco
• Router(config)# ip host 192.168.1.1 NewYork
Router(config)# enable password cisco
• Router(config)# line aux 0
Router(config-line)# login
Router(config-line)# password cisco
• Router(config)# enable password class
Router(config)# line vty 0 4
Router(config-line)# login
Router(config-line)# password cisco
Jawaban
• Router(config)# enable password class
Router(config)# line vty 0 4
Router(config-line)# login
Router(config-line)# password cisco
3. Which two types of information should be included in a business continuity plan? (Choose two.)
• maintenance time periods
• intrusion monitoring records
• offsite data storage procedures
• alternate IT processing locations*
• problem resolution escalation steps
Jawaban
• alternate IT processing locations*
• problem resolution escalation steps
4. Which two router parameters can be set from interface configuration mode? (Choose two.)
• IP address
• Telnet password
• hostname
• console password
• subnet mask
• enable secret password
Jawaban
• IP address
• subnet mask
5. Which two devices protect a corporate network against malicious attacks at the enterprise edge ?(Choose two.)
• demarc
• IP security (IPSec)
• Data Service Unit (DSU)
• intrusion prevention system (IPS)
• intrusion detection system (IDS)
6. Which three steps must be performed to remove all VLAN information from a switch but retain therest of the configuration? (Choose three.)
• Remove all VLAN associations from the interfaces.
• Remove the 802.1q encapsulation from the interfac
• Issue the command copy start run.
• Issue the command delete flash:vlan.dat.
• Issue the command erase start.
• Reload the switch.
7. What is the demarcation?
• physical point where the ISP responsibilty ends and the customer responsibilty begins
• physical location where all server farm connections meet before being distributed into the Core
• point of entry for outside attacks and is often vulnerable
• point of entry for all Access Layer connections from the Distribution Layer devices
8. Which device is responsible for moving packets between multiple network segments?
• router
• switch
• CSU/DSU
• IDS device
10. What information can an administrator learn using the show version command?
• Cisco IOS filename
• configured routing protocol
• status of each interface
• IP addresses of all interfaces
11. Which two situations require a network administrator to use out-of-band management to change arouter configuration? (Choose two.)
• Network links to the router are down.
• No Telnet password has been configured on the router.
• The administrator can only connect to the router using SSH.
• The network interfaces of the router are not configured with IP addresses.
• Company security policy requires that only HTTPS be used to connect to routers.
12. It is crucial that network administrators be able to examine and configure network devices fromtheir homes. Which two approaches allow this connectivity without increasing vulnerability to externalattacks? (Choose two.)
• Configure a special link at the POP to allow external entry from the home computer.
• Set up VPN access between the home computer and the network.
• Install a cable modem in the home to link to the network.
• Configure ACLs on the edge routers that allow only authorized users to access management portson network devices.
• Configure a server in the DMZ with a special username and password to allow external access.
13. A network administrator must define specific business processes to implement if a catastrophicdisaster prevents a company from performing daily business routines. Which portion of the networkdocumentation is the administrator defining?
• business security plan
• business continuity plan
• network solvency plan
• service level agreement
• network maintenance plan
14. A DoS attack crippled the daily operations of a large company for 8 hours. Which two optionscould be implemented by the network administrator to possibly prevent such an attack in the future?(Choose two.)
• install security devices with IDS and IPS at the enterprise edge
• reset all user passwords every 30 days
• filter packets based on IP address, traffic pattern, and protocol
• deny external workers VPN access to internal resources
• ensure critical devices are physically secure and placed behind the demarc
15. A network manager wants to have processes in place to ensure that network upgrades do not affectbusiness operations. What will the network manager create for this purpose?
• business security plan
• business continuity plan
• service level agreement
• network maintenance plan
16. An investment company has multiple servers that hold mission critical datThey are worried that ifsomething happens to these servers, they will lose this valuable information. Which type of plan isneeded for this company to help minimize loss in the event of a server crash?
• business security
• business continuity
• network maintenance
• service level agreement
17. When searching for information about authentication methods and usernames of companypersonnel, where can a network administrator look?
• Business Continuity Plan
• Business Security Plan
• Network Maintenance Plan
• Service Level Agreement
18. Refer to the exhibit. Which statement is true about port Fa5/1?
• When a violation is detected, the port will log the information to a syslog server.
• When a violation is detected, the port will go into err-disable mod
• There have been 11 security violations since the last reloa
• The port is currently in the shutdown state.
Kamis, 25 November 2010
modul ccna 3 dan 1
CCNA Discovery 3 Module 1 Exam Answers Version 4.0
1. What can be found at the enterprise edge?
• Internet, VPN, and WAN modules
• Internet, PSTN, and WAN services
• server farms and network management
• campus infrastructure, including access layer devices
Jawaban
• Internet, VPN, and WAN modules
2. In which functional area of the Cisco Enterprise Architecture should IDS and IPS be located to detect
• and prevent services from accessing hosts?
• Enterprise Campus
• Edge Distribution
• Enterprise Edge
• Service Provider Edge
Jawaban
• Enterprise Edge
3. A business consultant must use Internet websites to research a report on the e-business strategies of several firms and then electronically deliver the report to a group of clients in cities throughout the world. Which two teleworker tools can the consultant use to accomplish this project? (Choose two.)
• VoIP
• VPN
• HTTP
• Telnet
• email
Jawaban
• HTTP
• email
4. Which two measures help ensure that a hardware problem does not cause an outage in an enterprise LAN that supports mission critical services? (Choose two.)
• providing failover capability
• installing redundant power supplies
• purchasing more bandwidth from the ISP
• implementing broadcast containment with VLANs
• installing routers that can handle a greater amount of throughput
Jawaban
• providing failover capability
• installing redundant power supplies
5. Which task would typically only require services located at the access layer of the hierarchical design model?
• connecting to the corporate web server to update sales figures
• using a VPN from home to send data to the main office servers
• printing a meeting agenda on a local departmental network printer
• placing a VoIP call to a business associate in another country
• responding to an e-mail from a co-worker in another department
Jawaban
• printing a meeting agenda on a local departmental network printer
6. How does a VPN work to support remote user productivity?
• It uses SSL to encrypt remote user logins to the corporate intranet.
• It uses secure Telnet for remote user connections to internal network devices.
• It creates a virtual circuit that allows real-time communications between any two Internet endpoints.
• It uses encapsulation to create a secure tunnel for transmission of data across non-secure networks.
Jawaban
• It uses encapsulation to create a secure tunnel for transmission of data across non-secure networks.
7. A remote user needs to access a networking device on the internal network of the company. The transactions between the remote user and the device must be secure. Which protocol enables this to happen securely?
• HTTP
• SSH
• Telnet
• FTP
Jawaban
• SSH
8. What does VoIP provide to telecommuters?
• high-quality, live-video presentations
• real-time voice communications over the Internet
• ability to share desktop applications simultaneously
• secure, encrypted data transmissions through the Internet
9. Which functional component of the Cisco Enterprise Architecture is responsible for hosting internal servers?
• enterprise campus
• enterprise edge
• service provider edge
• building distribution
10. What is the purpose of the Cisco Enterprise Architecture?
• remove the three-layer hierarchical model and use a flat network approach
• divide the network into functional components while still maintaining the concept of Core, Distribution, and Access Layers
• provide services and functionality to the core layer by grouping various components into a single
• component located in the access layer
• reduce overall network traffic by grouping server farms, the management server, corporate intranet, and e-commerce routers in the same layer
11. Which two solutions would an enterprise IT department use to facilitate secure intranet access for remote workers? (Choose two.)
• VPN
• NAT
• user authentication
• client firewall software
• packet sniffing
12. Which statement describes the difference between an enterprise WAN and an enterprise extranet?
• An enterprise WAN is designed to interconnect local LANs, while an enterprise extranet is designed to interconnect remote branch offices.
• An enterprise WAN is designed to interconnect branch offices, while an enterprise extranet is designed to give access to external business partners.
• An enterprise WAN is designed to provide remote access for its teleworkers, while an enterprise extranet is designed to provide Internet connectivity for the enterprise.
• An enterprise WAN is designed to provide Internet connectivity for the enterprise, while an enterprise extranet is designed to provide remote access to the enterprise network for teleworkers.
13. Why would a network administrator want to limit the size of failure domains when designing a network?
• reduces the effect of Ethernet collisions
• reduces the impact of a key device or service failure
• reduces the impact of Internet congestion on critical traffic
• reduces the impact of blocking broadcast packets at the edge of the local network
14. What is the main purpose of the Access Layer in a hierarchically designed network?
• performs routing and packet manipulation
• supplies redundancy and failover protection
• provides a high-speed, low-latency backbone
• serves as a network connection point for end-user devices
15. Which three functions are performed at the Distribution Layer of the hierarchical network model? (Choose three.)
• forwards traffic that is destined for other networks
• isolates network problems to prevent them from affecting the Core Layer
• allows end users to access the local network
• provides a connection point for separate local networks
• transports large amounts of data between different geographic sites
• forwards traffic to other hosts on the same logical network
16. What is a benefit of having an extranet?
• It provides web-like access to company information for employees only.
• It limits access to corporate information to secure VPN or remote access connections only.
• It allows customers and partners to access company information by connecting to a public web server.
• It allows suppliers and contractors to access confidential internal information using controlled external connections.
17. What are two important characteristics or functions of devices at the Enterprise Edge? (Choose two.)
• providing Internet, telephone, and WAN services to the enterprise network
• providing a connection point for end-user devices to the enterprise network
• providing high-speed backbone connectivity with redundant connections
• providing intrusion detection and intrusion prevention to protect the network against malicious activity
• providing packet inspection to determine if incoming packets should be allowed on the enterprise network
18. Why is TCP the preferred Layer 4 protocol for transmitting data files?
• TCP is more reliable than UDP because it requires lost packets to be retransmitted.
• TCP requires less processing by the source and destination hosts than UDP.
• UDP introduces delays that degrade the quality of the data applications.
• TCP ensures fast delivery because it does not require sequencing or acknowlegements.
19. The ABC Corporation implements the network for its new headquarters using the Cisco Enterprise Architecture. The network administrator wants to filter the traffic from and to the outside world. Where should the administrator deploy a firewall device?
• server farm
• enterprise edge
• enterprise campus
• service provider edge
20. Which two statements are reasons why UDP is used for voice and video traffic instead of TCP?(Choose two.)
• TCP requires all data packets to be delivered for the data to be usable.
• The acknowledgment process of TCP introduces delays that break the streams of data.
• UDP does not have mechanisms for retransmitting lost packets.
• UDP tolerates delays and compensates for them.
• TCP is a connectionless protocol that provides end-to-end reliability.
• UDP is a connection-oriented protocol that provides end-to-end reliability.
1. What can be found at the enterprise edge?
• Internet, VPN, and WAN modules
• Internet, PSTN, and WAN services
• server farms and network management
• campus infrastructure, including access layer devices
Jawaban
• Internet, VPN, and WAN modules
2. In which functional area of the Cisco Enterprise Architecture should IDS and IPS be located to detect
• and prevent services from accessing hosts?
• Enterprise Campus
• Edge Distribution
• Enterprise Edge
• Service Provider Edge
Jawaban
• Enterprise Edge
3. A business consultant must use Internet websites to research a report on the e-business strategies of several firms and then electronically deliver the report to a group of clients in cities throughout the world. Which two teleworker tools can the consultant use to accomplish this project? (Choose two.)
• VoIP
• VPN
• HTTP
• Telnet
Jawaban
• HTTP
4. Which two measures help ensure that a hardware problem does not cause an outage in an enterprise LAN that supports mission critical services? (Choose two.)
• providing failover capability
• installing redundant power supplies
• purchasing more bandwidth from the ISP
• implementing broadcast containment with VLANs
• installing routers that can handle a greater amount of throughput
Jawaban
• providing failover capability
• installing redundant power supplies
5. Which task would typically only require services located at the access layer of the hierarchical design model?
• connecting to the corporate web server to update sales figures
• using a VPN from home to send data to the main office servers
• printing a meeting agenda on a local departmental network printer
• placing a VoIP call to a business associate in another country
• responding to an e-mail from a co-worker in another department
Jawaban
• printing a meeting agenda on a local departmental network printer
6. How does a VPN work to support remote user productivity?
• It uses SSL to encrypt remote user logins to the corporate intranet.
• It uses secure Telnet for remote user connections to internal network devices.
• It creates a virtual circuit that allows real-time communications between any two Internet endpoints.
• It uses encapsulation to create a secure tunnel for transmission of data across non-secure networks.
Jawaban
• It uses encapsulation to create a secure tunnel for transmission of data across non-secure networks.
7. A remote user needs to access a networking device on the internal network of the company. The transactions between the remote user and the device must be secure. Which protocol enables this to happen securely?
• HTTP
• SSH
• Telnet
• FTP
Jawaban
• SSH
8. What does VoIP provide to telecommuters?
• high-quality, live-video presentations
• real-time voice communications over the Internet
• ability to share desktop applications simultaneously
• secure, encrypted data transmissions through the Internet
9. Which functional component of the Cisco Enterprise Architecture is responsible for hosting internal servers?
• enterprise campus
• enterprise edge
• service provider edge
• building distribution
10. What is the purpose of the Cisco Enterprise Architecture?
• remove the three-layer hierarchical model and use a flat network approach
• divide the network into functional components while still maintaining the concept of Core, Distribution, and Access Layers
• provide services and functionality to the core layer by grouping various components into a single
• component located in the access layer
• reduce overall network traffic by grouping server farms, the management server, corporate intranet, and e-commerce routers in the same layer
11. Which two solutions would an enterprise IT department use to facilitate secure intranet access for remote workers? (Choose two.)
• VPN
• NAT
• user authentication
• client firewall software
• packet sniffing
12. Which statement describes the difference between an enterprise WAN and an enterprise extranet?
• An enterprise WAN is designed to interconnect local LANs, while an enterprise extranet is designed to interconnect remote branch offices.
• An enterprise WAN is designed to interconnect branch offices, while an enterprise extranet is designed to give access to external business partners.
• An enterprise WAN is designed to provide remote access for its teleworkers, while an enterprise extranet is designed to provide Internet connectivity for the enterprise.
• An enterprise WAN is designed to provide Internet connectivity for the enterprise, while an enterprise extranet is designed to provide remote access to the enterprise network for teleworkers.
13. Why would a network administrator want to limit the size of failure domains when designing a network?
• reduces the effect of Ethernet collisions
• reduces the impact of a key device or service failure
• reduces the impact of Internet congestion on critical traffic
• reduces the impact of blocking broadcast packets at the edge of the local network
14. What is the main purpose of the Access Layer in a hierarchically designed network?
• performs routing and packet manipulation
• supplies redundancy and failover protection
• provides a high-speed, low-latency backbone
• serves as a network connection point for end-user devices
15. Which three functions are performed at the Distribution Layer of the hierarchical network model? (Choose three.)
• forwards traffic that is destined for other networks
• isolates network problems to prevent them from affecting the Core Layer
• allows end users to access the local network
• provides a connection point for separate local networks
• transports large amounts of data between different geographic sites
• forwards traffic to other hosts on the same logical network
16. What is a benefit of having an extranet?
• It provides web-like access to company information for employees only.
• It limits access to corporate information to secure VPN or remote access connections only.
• It allows customers and partners to access company information by connecting to a public web server.
• It allows suppliers and contractors to access confidential internal information using controlled external connections.
17. What are two important characteristics or functions of devices at the Enterprise Edge? (Choose two.)
• providing Internet, telephone, and WAN services to the enterprise network
• providing a connection point for end-user devices to the enterprise network
• providing high-speed backbone connectivity with redundant connections
• providing intrusion detection and intrusion prevention to protect the network against malicious activity
• providing packet inspection to determine if incoming packets should be allowed on the enterprise network
18. Why is TCP the preferred Layer 4 protocol for transmitting data files?
• TCP is more reliable than UDP because it requires lost packets to be retransmitted.
• TCP requires less processing by the source and destination hosts than UDP.
• UDP introduces delays that degrade the quality of the data applications.
• TCP ensures fast delivery because it does not require sequencing or acknowlegements.
19. The ABC Corporation implements the network for its new headquarters using the Cisco Enterprise Architecture. The network administrator wants to filter the traffic from and to the outside world. Where should the administrator deploy a firewall device?
• server farm
• enterprise edge
• enterprise campus
• service provider edge
20. Which two statements are reasons why UDP is used for voice and video traffic instead of TCP?(Choose two.)
• TCP requires all data packets to be delivered for the data to be usable.
• The acknowledgment process of TCP introduces delays that break the streams of data.
• UDP does not have mechanisms for retransmitting lost packets.
• UDP tolerates delays and compensates for them.
• TCP is a connectionless protocol that provides end-to-end reliability.
• UDP is a connection-oriented protocol that provides end-to-end reliability.
Rabu, 17 November 2010
ccna 2.8
CCNA Discovery 2 Module 8 Exam Answers Version 4.0
1. • accounting
2. • date and time of message
• ID of sending device
• message ID
3. • It uses a 128-bit pre-shared hexadecimal key to prevent unauthorized wireless access.
4. • packet filtering
5. • authentication
6. • reviewing backup logs
• performing trial backups
7. • poll
8. • SNMP
• Telnet
• TFTP
9. • The hacker obtained the MAC address of a permitted host, and cloned it on his wireless laptop NIC.
10. • Provide users with only the access to resources required to do their jobs.
• Allow users to decide how much permission they need to accomplish their job tasks.
11. • IPSEC
• SSL
• HTTPS
12. • encryption
13. • network management database
14. • Tape is not a cost-effective means of backing up data.
• Tape drives require regular cleaning to maintain reliability.
15. • DMZ
16. • ports
• protocols
17. • when the management interface of a device is not reachable across the network
18. • IPSEC
19. • full
20. • authentication
1. • accounting
2. • date and time of message
• ID of sending device
• message ID
3. • It uses a 128-bit pre-shared hexadecimal key to prevent unauthorized wireless access.
4. • packet filtering
5. • authentication
6. • reviewing backup logs
• performing trial backups
7. • poll
8. • SNMP
• Telnet
• TFTP
9. • The hacker obtained the MAC address of a permitted host, and cloned it on his wireless laptop NIC.
10. • Provide users with only the access to resources required to do their jobs.
• Allow users to decide how much permission they need to accomplish their job tasks.
11. • IPSEC
• SSL
• HTTPS
12. • encryption
13. • network management database
14. • Tape is not a cost-effective means of backing up data.
• Tape drives require regular cleaning to maintain reliability.
15. • DMZ
16. • ports
• protocols
17. • when the management interface of a device is not reachable across the network
18. • IPSEC
19. • full
20. • authentication
ccna 2.7
CCNA Discovery 2 Module 7 Exam Answers Version 4.0
1. • The OSI network layer is comparable to the Internet layer of the TCP/IP model.
• The TCP/IP model is based on four layers and the OSI model is based on seven layers.
2.• availability
• scalability
3. • It utilizes TCP port 110.
• SMTP is used to send the e-mail message to the mail servers.
4. • Host2 sends a SYN-ACK message to Host1.
5. • Redundant hardware provides enhanced reliability.
• Fault tolerance is a measure of reliability.
• The longer the MTBF, the greater the reliability.
6. • The protocol interpreter is responsible for the data transfer function.
• In passive data connections, the FTP client initiates the transfer of data.
7. • It enables the synchronization of port numbers between source and destination hosts.
8. • It supports authentication.
• It encrypts packets with SSL.
• It requires additional server processing time.
9. • reverse lookup
10. • dynamic
11. • The command ping fileserv will use IP address 172.16.5.10.
12. • mapping name-to-IP addresses for internal hosts
• forwarding name resolution requests to a caching-only server
13. • low overhead
• no flow control
• no error-recovery function
14. • FTP
• HTTP
• SMTP
15. • HTTP – 80
• SMTP – 25
16. • source IP address and port with a destination IP address and port
17. • SMTP
18. • Source – 192.168.1.17:80 ; Destination – 192.168.2.39:1045
19. • caching-only
20. • The server will determine the appropriate service from the destination port field.
21. • IP address
• MAC address
1. • The OSI network layer is comparable to the Internet layer of the TCP/IP model.
• The TCP/IP model is based on four layers and the OSI model is based on seven layers.
2.• availability
• scalability
3. • It utilizes TCP port 110.
• SMTP is used to send the e-mail message to the mail servers.
4. • Host2 sends a SYN-ACK message to Host1.
5. • Redundant hardware provides enhanced reliability.
• Fault tolerance is a measure of reliability.
• The longer the MTBF, the greater the reliability.
6. • The protocol interpreter is responsible for the data transfer function.
• In passive data connections, the FTP client initiates the transfer of data.
7. • It enables the synchronization of port numbers between source and destination hosts.
8. • It supports authentication.
• It encrypts packets with SSL.
• It requires additional server processing time.
9. • reverse lookup
10. • dynamic
11. • The command ping fileserv will use IP address 172.16.5.10.
12. • mapping name-to-IP addresses for internal hosts
• forwarding name resolution requests to a caching-only server
13. • low overhead
• no flow control
• no error-recovery function
14. • FTP
• HTTP
• SMTP
15. • HTTP – 80
• SMTP – 25
16. • source IP address and port with a destination IP address and port
17. • SMTP
18. • Source – 192.168.1.17:80 ; Destination – 192.168.2.39:1045
19. • caching-only
20. • The server will determine the appropriate service from the destination port field.
21. • IP address
• MAC address
ccna 2.6
CCNA Discovery 2 Module 6 Exam Answers Version 4.0
1. • show ip protocols
2. • 16
3. • when the company uses two or more ISPs
4. • a RIP router
5. • Interior routing protocols are used to route on the Internet. Exterior routing protocols are used inside organizations.
6. • subnet mask
7. • EIGRP
8. • routerA(config-router)# network 192.168.3.0
9. • Immediately
10. • All routers at an ISP must be assigned the same AS number.
11. • to identify which networks on the router will send and receive RIP updates
12. • router# show ip networks
13. • It allows a router to share information about known networks with other routers.
14. • border gateway router
15. • show ip rip database
16. • destination IP address
17. • a global business with connections to multiple local ISPs
• a medium-sized nationwide business with Internet connectivity through different ISPs
18. • show ip rip database
19. • Routers will not allow packets to be forwarded until the network has converged.
20. • They require manual reconfiguration to accommodate network changes.
• They are identified in the routing table with the prefix S
21. • Link-state routers only know about directly connected routers. Distance vector routers know about every router in the network.
• Link-state routing protocols update when a change is made. A network using distance vector routing protocols only updates at a specific interval.
22. • BGP
23. • Ping
• Traceroute
• show ip route
24. • autonomous system
1. • show ip protocols
2. • 16
3. • when the company uses two or more ISPs
4. • a RIP router
5. • Interior routing protocols are used to route on the Internet. Exterior routing protocols are used inside organizations.
6. • subnet mask
7. • EIGRP
8. • routerA(config-router)# network 192.168.3.0
9. • Immediately
10. • All routers at an ISP must be assigned the same AS number.
11. • to identify which networks on the router will send and receive RIP updates
12. • router# show ip networks
13. • It allows a router to share information about known networks with other routers.
14. • border gateway router
15. • show ip rip database
16. • destination IP address
17. • a global business with connections to multiple local ISPs
• a medium-sized nationwide business with Internet connectivity through different ISPs
18. • show ip rip database
19. • Routers will not allow packets to be forwarded until the network has converged.
20. • They require manual reconfiguration to accommodate network changes.
• They are identified in the routing table with the prefix S
21. • Link-state routers only know about directly connected routers. Distance vector routers know about every router in the network.
• Link-state routing protocols update when a change is made. A network using distance vector routing protocols only updates at a specific interval.
22. • BGP
23. • Ping
• Traceroute
• show ip route
24. • autonomous system
Rabu, 10 November 2010
CCNA 2.5
CCNA Discovery 2 Module 5 Exam Answers Version 4.0
1. vIn what two ways does SDM differ from the IOS CLI? (Choose two.)
• SDM is used for in-band management only. The IOS CLI can be used for in-band and out-of-band management.
• SDM is accessed through a Telnet application. The IOS CLI is accessed through a web browser.
• SDM is available for all router platforms. The IOS CLI is available for a limited number of Cisco devices.
• SDM utilizes GUI buttons and text boxes. The IOS CLI requires the use of text-based commands.
• SDM is used for advanced configuration tasks. The IOS CLI is preferred for initial basic device configuration. 2. Which mode will a configured router display at login?
• global configuration mode
• setup mode
• ROM monitor mode
• user EXEC mode
• SDM is used for in-band management only. The IOS CLI can be used for in-band and out-of-band management.
• SDM is accessed through a Telnet application. The IOS CLI is accessed through a web browser.
• SDM is available for all router platforms. The IOS CLI is available for a limited number of Cisco devices.
• SDM utilizes GUI buttons and text boxes. The IOS CLI requires the use of text-based commands.
• SDM is used for advanced configuration tasks. The IOS CLI is preferred for initial basic device configuration. 2. Which mode will a configured router display at login?
• global configuration mode
• setup mode
• ROM monitor mode
• user EXEC mode
3. Refer to the exhibit. Which password or passwords will be encrypted as a result of the configuration that is shown?
• virtual terminal only
• enable mode only
• console and virtual terminal only
• enable mode and virtual terminal
• only the service password
• all configured passwords 4.Refer to the exhibit. Which three sets of commands are required to enable administrators to connect to the Switch1 console over Telnet for configuration and management? (Choose three.)
• Switch1(config)# interface fa0/1
Switch1(config-if)# ip address 192.168.2.64 255.255.255.192
• Switch1(config)# interface fa0/1
Switch1(config-if)# ip address 192.168.2.66 255.255.255.192
• Switch1(config)# interface vlan 1
Switch1(config-if)# ip address 192.168.2.126 255.255.255.192
Switch1(config-if)# no shutdown
• Switch1(config)# line vty 0 4
Switch1(config-line)# enable password cisco
Switch1(config-line)# login
• Switch1(config)# line vty 0 15
Switch1(config-line)# password cisco
Switch1(config-line)# login
• Switch1(config)# ip default-gateway 192.168.2.65
• virtual terminal only
• enable mode only
• console and virtual terminal only
• enable mode and virtual terminal
• only the service password
• all configured passwords 4.Refer to the exhibit. Which three sets of commands are required to enable administrators to connect to the Switch1 console over Telnet for configuration and management? (Choose three.)
• Switch1(config)# interface fa0/1
Switch1(config-if)# ip address 192.168.2.64 255.255.255.192
• Switch1(config)# interface fa0/1
Switch1(config-if)# ip address 192.168.2.66 255.255.255.192
• Switch1(config)# interface vlan 1
Switch1(config-if)# ip address 192.168.2.126 255.255.255.192
Switch1(config-if)# no shutdown
• Switch1(config)# line vty 0 4
Switch1(config-line)# enable password cisco
Switch1(config-line)# login
• Switch1(config)# line vty 0 15
Switch1(config-line)# password cisco
Switch1(config-line)# login
• Switch1(config)# ip default-gateway 192.168.2.65
5. How does the SYST LED on the catalyst 2960 switch indicate a POST failure?
• blinks rapidly amber
• blinks rapidly green
• steady amber
• steady green 6. Refer to the exhibit. A company always uses the last valid IP address in a subnetwork as the IP address of the router LAN interface. A network administrator is using a laptop to configure switch X with a default gateway. Assuming that the switch IP address is 192.168.5.147/24, what command will the administrator use to assign a default gateway to the switch?
• X(config)# ip default-gateway 192.168.5.254
• X(config)# ip gateway 192.168.5.1
• X(config)# ip route 0.0.0.0 0.0.0.0 192.168.5.1
• X(config)# ip default-route 192.168.5.1
• X(config)# ip route 192.168.5.254 255.255.255.0 fastethernet 0/0
7. A technician has made changes to the configuration of a router. What command will allow the technician to view the current configuration before he saves the changes?
• router# show running-config
• router# show startup-config
• router# show flash
• router# show version
8. Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.)
• VTY interface
• console interface
• Ethernet interface
• secret EXEC mode
• privileged EXEC mode
• router configuration mode
9. To save time, IOS commands may be partially entered and then completed by typing which key or key combination?
• Tab
• Ctrl-P
• Ctrl-N
• Up Arrow
• Right Arrow
• Down Arrow
10. What is the correct command sequence to configure a router host name to ‘LAB_A’?
• Router> enable
Router# configure terminal
Router(config)# hostname LAB_A
• Router> enable
Router# hostname LAB_A
• Router> enable
Router# configure router
Router(config)# hostname LAB_A
• Router> enable
Router(config)# host name LAB_A
11. Refer to the exhibit. From the router console, an administrator is unable to ping a Catalyst switch that is located in another building. What can the administrator do from her location to check the IP configuration of the attached switch?
• Open an SDM session with the switch from her desktop.
• Telnet to the switch from the router console.
• Use the show cdp neighbors detail command from the router console.
• The administrator must go to the switch location and make a console connection to check these settings.
12. Which two options must be selected in SDM Express to enable a router serial interface to obtain an IP address automatically? (Choose two.)
• Easy IP (IP negotiated)
• IP unnumbered
• No IP address
• HDLC encapsulation
• Frame Relay encapsulation
• PPP encapsulation
• blinks rapidly amber
• blinks rapidly green
• steady amber
• steady green 6. Refer to the exhibit. A company always uses the last valid IP address in a subnetwork as the IP address of the router LAN interface. A network administrator is using a laptop to configure switch X with a default gateway. Assuming that the switch IP address is 192.168.5.147/24, what command will the administrator use to assign a default gateway to the switch?
• X(config)# ip default-gateway 192.168.5.254
• X(config)# ip gateway 192.168.5.1
• X(config)# ip route 0.0.0.0 0.0.0.0 192.168.5.1
• X(config)# ip default-route 192.168.5.1
• X(config)# ip route 192.168.5.254 255.255.255.0 fastethernet 0/0
7. A technician has made changes to the configuration of a router. What command will allow the technician to view the current configuration before he saves the changes?
• router# show running-config
• router# show startup-config
• router# show flash
• router# show version
8. Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.)
• VTY interface
• console interface
• Ethernet interface
• secret EXEC mode
• privileged EXEC mode
• router configuration mode
9. To save time, IOS commands may be partially entered and then completed by typing which key or key combination?
• Tab
• Ctrl-P
• Ctrl-N
• Up Arrow
• Right Arrow
• Down Arrow
10. What is the correct command sequence to configure a router host name to ‘LAB_A’?
• Router> enable
Router# configure terminal
Router(config)# hostname LAB_A
• Router> enable
Router# hostname LAB_A
• Router> enable
Router# configure router
Router(config)# hostname LAB_A
• Router> enable
Router(config)# host name LAB_A
11. Refer to the exhibit. From the router console, an administrator is unable to ping a Catalyst switch that is located in another building. What can the administrator do from her location to check the IP configuration of the attached switch?
• Open an SDM session with the switch from her desktop.
• Telnet to the switch from the router console.
• Use the show cdp neighbors detail command from the router console.
• The administrator must go to the switch location and make a console connection to check these settings.
12. Which two options must be selected in SDM Express to enable a router serial interface to obtain an IP address automatically? (Choose two.)
• Easy IP (IP negotiated)
• IP unnumbered
• No IP address
• HDLC encapsulation
• Frame Relay encapsulation
• PPP encapsulation
13. What three settings can be made in the SDM Express basic configuration screen? (Choose three.)
• host name
• DHCP options
• domain name
• interface IP addresses
• enable secret password
• DNS server IP addresses 14. Which tasks can be accomplished by using the command history feature? (Choose two.)
• View a list of commands entered in a previous session.
• Recall up to 15 command lines by default.
• Set the command history buffer size.
• Recall previously entered commands.
• Save command lines in a log file for future reference.
15. What option within Cisco SDM Express must be configured to allow hosts that receive IP address settings from the router to resolve names on the network or Internet?
• host name
• domain name
• DHCP address pool
• DNS server IP address
16. Which three encapsulation types can be set on a serial interface by an administrator who is using SDM Express? (Choose three.)
• ATM
• CHAP
• Frame Relay
• HDLC
• PAP
• PPP
17. Which command will display routing table information about all known networks and subnetworks?
• Router# show ip interfaces
• Router# show ip connections
• Router# show ip route
• Router# show ip networks
18. A network administrator needs to configure a router. Which of the following connection methods requires network functionality to be accessible?
• console
• AUX
• Telnet
• modem
19. Which three pieces of information about a neighbor device can be obtained by the show cdp neighbors command? (Choose three.)
• platform
• routing protocol
• connected interface of neighbor device
• device ID
• IP addresses of all interfaces
• enable mode password
20.Which function is a unique responsibility of the DCE devices shown in the exhibit?
• transmission of data
• reception of data
• clocking for the synchronous link
• noise cancellation in transmitted data
21. Which of the following are functions of NVRAM? (Choose two.)
• stores the routing table
• retains contents when power is removed
• stores the startup configuration file
• contains the running configuration file
• stores the ARP table
22. Refer to the exhibit. Which series of commands will enable users who are attached to Router1 to access the remote server?
• Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.129 255.255.255.252
Router1(config-if)# clock rate 64000
Router1(config-if)# no shutdown
• Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.125 255.255.255.252
Router1(config-if)# no shutdown
• Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.125 255.255.255.252
Router1(config-if)# clock rate 64000
Router1(config-if)# no shutdown
• Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.129 255.255.255.252
Router1(config-if)# no shutdown
23. A network technician is attempting to add an older workstation to a Cisco switched LAN. The technician has manually configured the workstation to full-duplex mode in order to enhance the network performance of the workstation. However, when the device is attached to the network, performance degrades and excess collision are detected. What is the cause of this problem?
• The host is configured in a different subnet from the subnet of the switch.
• There is a duplex mismatch between the workstation and switch port.
• The switch port is running at a different speed from the speed of the workstation NIC.
• The host has been configured with a default gateway that is different from that of the switch.
24. Which of the following statements are true regarding the user EXEC mode? (Choose two.)
• All router commands are available.
• Global configuration mode can be accessed by entering the enable command.
• A password can be entered to allow access to other modes.
• Interfaces and routing protocols can be configured.
• Only some aspects of the router configuration can be viewed.
25. Which command turns on a router interface?
• Router(config-if)# enable
• Router(config-if)# no down
• Router(config-if)# s0 active
• Router(config-if)# interface up
• Router(config-if)# no shutdown
• host name
• DHCP options
• domain name
• interface IP addresses
• enable secret password
• DNS server IP addresses 14. Which tasks can be accomplished by using the command history feature? (Choose two.)
• View a list of commands entered in a previous session.
• Recall up to 15 command lines by default.
• Set the command history buffer size.
• Recall previously entered commands.
• Save command lines in a log file for future reference.
15. What option within Cisco SDM Express must be configured to allow hosts that receive IP address settings from the router to resolve names on the network or Internet?
• host name
• domain name
• DHCP address pool
• DNS server IP address
16. Which three encapsulation types can be set on a serial interface by an administrator who is using SDM Express? (Choose three.)
• ATM
• CHAP
• Frame Relay
• HDLC
• PAP
• PPP
17. Which command will display routing table information about all known networks and subnetworks?
• Router# show ip interfaces
• Router# show ip connections
• Router# show ip route
• Router# show ip networks
18. A network administrator needs to configure a router. Which of the following connection methods requires network functionality to be accessible?
• console
• AUX
• Telnet
• modem
19. Which three pieces of information about a neighbor device can be obtained by the show cdp neighbors command? (Choose three.)
• platform
• routing protocol
• connected interface of neighbor device
• device ID
• IP addresses of all interfaces
• enable mode password
20.Which function is a unique responsibility of the DCE devices shown in the exhibit?
• transmission of data
• reception of data
• clocking for the synchronous link
• noise cancellation in transmitted data
21. Which of the following are functions of NVRAM? (Choose two.)
• stores the routing table
• retains contents when power is removed
• stores the startup configuration file
• contains the running configuration file
• stores the ARP table
22. Refer to the exhibit. Which series of commands will enable users who are attached to Router1 to access the remote server?
• Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.129 255.255.255.252
Router1(config-if)# clock rate 64000
Router1(config-if)# no shutdown
• Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.125 255.255.255.252
Router1(config-if)# no shutdown
• Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.125 255.255.255.252
Router1(config-if)# clock rate 64000
Router1(config-if)# no shutdown
• Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.129 255.255.255.252
Router1(config-if)# no shutdown
23. A network technician is attempting to add an older workstation to a Cisco switched LAN. The technician has manually configured the workstation to full-duplex mode in order to enhance the network performance of the workstation. However, when the device is attached to the network, performance degrades and excess collision are detected. What is the cause of this problem?
• The host is configured in a different subnet from the subnet of the switch.
• There is a duplex mismatch between the workstation and switch port.
• The switch port is running at a different speed from the speed of the workstation NIC.
• The host has been configured with a default gateway that is different from that of the switch.
24. Which of the following statements are true regarding the user EXEC mode? (Choose two.)
• All router commands are available.
• Global configuration mode can be accessed by entering the enable command.
• A password can be entered to allow access to other modes.
• Interfaces and routing protocols can be configured.
• Only some aspects of the router configuration can be viewed.
25. Which command turns on a router interface?
• Router(config-if)# enable
• Router(config-if)# no down
• Router(config-if)# s0 active
• Router(config-if)# interface up
• Router(config-if)# no shutdown
CCNA 2.4
CCNA Discovery 2 Module 4 Exam Answers Version 4.0
1. In an 8 bit binary number, what is the total number of combinations of the eight bits?
• 128
• 254
• 255
• 256
• 512
• 1024
• 128
• 254
• 255
• 256
• 512
• 1024
2. Convert the decimal number 231 into its binary equivalent. Select the correct answer from the list below.
• 11110010
• 11011011
• 11110110
• 11100111
• 11100101
• 11101110
• 11110010
• 11011011
• 11110110
• 11100111
• 11100101
• 11101110
3. How many usable hosts are available given a Class C IP address with the default subnet mask?
• 254
• 255
• 256
• 510
• 511
• 512
• 254
• 255
• 256
• 510
• 511
• 512
4. Which statement describes NAT overload or PAT?
• Each internal address is dynamically translated to an individual external IP address.
• A single internal address is always translated to the same unique external IP address.
• Many internal addresses can be translated to a single IP address using different port assignments.
• Many internal addresses are statically assigned a single IP address and port to use for communications.
• Each internal address is dynamically translated to an individual external IP address.
• A single internal address is always translated to the same unique external IP address.
• Many internal addresses can be translated to a single IP address using different port assignments.
• Many internal addresses are statically assigned a single IP address and port to use for communications.
5. Which IPv4 class of addresses provides the most networks?
• Class A
• Class B
• Class C
• Class D
• Class E
• Class A
• Class B
• Class C
• Class D
• Class E
6. Which statement accurately describes public IP addresses?
• Public addresses cannot be used within a private network.
• Public IP addresses must be unique across the entire Internet.
• Public addresses can be duplicated only within a local network.
• Public IP addresses are only required to be unique within the local network.
• Network administrators are free to select any public addresses to use for network devices that access the Internet.
• Public addresses cannot be used within a private network.
• Public IP addresses must be unique across the entire Internet.
• Public addresses can be duplicated only within a local network.
• Public IP addresses are only required to be unique within the local network.
• Network administrators are free to select any public addresses to use for network devices that access the Internet.
7. Which two statements describe classful IP addresses? (Choose two.)
• It is possible to determine which class an address belongs to by reading the first bit.
• The number of bits used to identify the hosts is fixed by the class of the network.
• Only Class A addresses can be represented by high-order bits 100.
• Up to 24 bits can make up the host portion of a Class C address.
• Up to 24 bits can be used to identify unique networks.
• Three of the five classes of addresses are reserved for multicasts and experimental use.
• It is possible to determine which class an address belongs to by reading the first bit.
• The number of bits used to identify the hosts is fixed by the class of the network.
• Only Class A addresses can be represented by high-order bits 100.
• Up to 24 bits can make up the host portion of a Class C address.
• Up to 24 bits can be used to identify unique networks.
• Three of the five classes of addresses are reserved for multicasts and experimental use.
8. Company XYZ uses a network address of 192.168.4.0. It uses the mask of 255.255.255.224 to create subnets. What is the maximum number of usable hosts in each subnet?
• 6
• 14
• 30
• 62
• 6
• 14
• 30
• 62
9. hat is the network broadcast address for a Class C address of 192.168.32.0 with the default subnet mask?
• 192.168.0.0
• 192.168.0.255
• 192.168.32.0
• 192.168.32.254
• 192.168.32.255
• 192.168.0.0
• 192.168.0.255
• 192.168.32.0
• 192.168.32.254
• 192.168.32.255
10.
Refer to the exhibit. Host A is connected to the LAN, but it cannot get access to any resources on the Internet. The configuration of the host is shown in the exhibit. What could be the cause of the problem?
• The host subnet mask is incorrect.
• The default gateway is a network address.
• The default gateway is a broadcast address.
• The default gateway is on a different subnet from the host.
Refer to the exhibit. Host A is connected to the LAN, but it cannot get access to any resources on the Internet. The configuration of the host is shown in the exhibit. What could be the cause of the problem?
• The host subnet mask is incorrect.
• The default gateway is a network address.
• The default gateway is a broadcast address.
• The default gateway is on a different subnet from the host.
11. IPv6 increases the IP address size from 32 bits to how many bits?
• 64
• 96
• 128
• 192
• 256
• 512
• 64
• 96
• 128
• 192
• 256
• 512
12. What is the range of the first octet in a Class B address?
• 127 to 191
• 127 to 192
• 128 to 191
• 128 to 192
• 127 to 191
• 127 to 192
• 128 to 191
• 128 to 192
13. Which IPv4 class provides the highest number of host addresses per network?
• Class A
• Class B
• Class C
• Class D
• Class E
• Class A
• Class B
• Class C
• Class D
• Class E
14.
refer to the exhibit. Which range of IP addresses would allow hosts that are connected to the Router1 Fa0/0 interface to access outside networks?
• 192.168.1.0 through 192.168.1.95
• 192.168.1.66 through 192.168.1.94
• 192.168.1.66 through 192.168.1.96
• 192.168.1.0 through 192.168.1.127
• 192.168.1.66 through 192.168.1.128
refer to the exhibit. Which range of IP addresses would allow hosts that are connected to the Router1 Fa0/0 interface to access outside networks?
• 192.168.1.0 through 192.168.1.95
• 192.168.1.66 through 192.168.1.94
• 192.168.1.66 through 192.168.1.96
• 192.168.1.0 through 192.168.1.127
• 192.168.1.66 through 192.168.1.128
15. Which option shows the proper notation for an IPv6 address?
• 2001,0db8,3c55,0015,abcd,ff13
• 2001-0db8-3c55-0015-abcd-ff13
• 2001.0db8.3c55.0015.abcd.ff13
• 2001:0db8:3c55:0015::abcd:ff13
• 2001,0db8,3c55,0015,abcd,ff13
• 2001-0db8-3c55-0015-abcd-ff13
• 2001.0db8.3c55.0015.abcd.ff13
• 2001:0db8:3c55:0015::abcd:ff13
16. What are two reasons that NAT was developed? (Choose two.)
• to preserve registered public IP addresses
• to allow users on the public Internet to access local networks
• to provide a method for privately addressed LANs to participate in the Internet
• to make routing protocols operate more efficiently
• to allow private addresses to be routed on the public Internet
• to reduce overhead and CPU usage on gateway routers
• to preserve registered public IP addresses
• to allow users on the public Internet to access local networks
• to provide a method for privately addressed LANs to participate in the Internet
• to make routing protocols operate more efficiently
• to allow private addresses to be routed on the public Internet
• to reduce overhead and CPU usage on gateway routers
17. What must happen for a privately addressed host on an inside local network to be able to communicate with an outside destination host on the Internet?
• The host IP address must be translated to an outside private address.
• The host IP address must be translated to an inside local address.
• The host IP address must be translated to an outside local address.
• The host IP address must be translated to an inside global address.
• The host IP address must be translated to an outside private address.
• The host IP address must be translated to an inside local address.
• The host IP address must be translated to an outside local address.
• The host IP address must be translated to an inside global address.
18. Which port numbers are used by PAT to create unique global addresses?
• 255 and below
• 1024 and below
• 1025 and above
• 64,000 and above
• 255 and below
• 1024 and below
• 1025 and above
• 64,000 and above
19. Static NAT works by mapping a specific inside local IP address to what other specific address type?
• inside global
• outside local
• outside global
• private IP address
• inside global
• outside local
• outside global
• private IP address
20. What are three advantages of NAT implementations? (Choose three.)
• improved security
• improved router performance
• decreased processor load
• improved scalability
• universal application compatibility
• sharing few public IP addresses with many hosts
• improved security
• improved router performance
• decreased processor load
• improved scalability
• universal application compatibility
• sharing few public IP addresses with many hosts
Langganan:
Postingan (Atom)